Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterGenie Torsion Spring Replacement: The Fort Worth Owner’s Guide
We stock and install Genie-compatible torsion spring replacements for Fort Worth homes, with most jobs running $180-$340 installed and completed the same day you call. Our trucks carry the common wire sizes and inside diameters that match Genie opener systems, so we don’t leave you waiting on a parts order. You’ll usually discover the problem when the door won’t lift, lifts unevenly, or slams shut - often after a loud bang from the garage that sounds like a firecracker.
Which Genie Models This Applies To
Genie has used consistent torsion spring configurations across their screw drive, chain drive, and belt drive opener lines for decades. The spring itself isn’t branded to the opener - it’s sized to your door’s weight and height - but Genie systems often pair with lighter-duty springs on older installations that weren’t specced correctly for Fort Worth’s heavier insulated steel doors.
To identify what you need, check the winding cone for a stamp showing wire gauge, inside diameter, and overall length. Common Genie-compatible setups we see in Fort Worth run .225 to .250 wire, 1.75″ or 2″ inside diameter, with lengths from 24″ to 32″ depending on door height. The label on your opener head unit (model 1022, 1024, 2024, 2055, 3055, 3155, or similar) tells us the vintage and helps confirm spring spec, but the door itself determines the spring.
We carry both OEM-equivalent and quality aftermarket springs. For most Fort Worth homeowners, the aftermarket spring we stock matches OEM cycle life at a lower parts cost. We quote both options and let you decide.
Mainspring Garage Door Co. is an independent service provider. We are not affiliated with Genie.
Signs Your Genie Torsion Spring Replacement Is Failing
- The door feels heavy or won’t stay open. A torsion spring stores energy to offset the door’s weight. When it loses tension through metal fatigue, that weight transfers straight to your Genie opener motor and your back. In Fort Worth’s heat, we see this accelerate when springs were undersized for the door from the start.
- You heard a loud snap from the garage, often at night. That’s the sound of a spring breaking under load. The remaining spring, if you have a two-spring system, carries double the weight and won’t last long. We replace these in pairs so you’re not calling us again in three months.
- The door opens crooked or one cable hangs slack. A broken spring on one side throws the whole system off balance. Your Genie opener strain compensates until it can’t, and then the safety reverse triggers or the motor burns out.
- The Genie opener strains, hums, or reverses mid-travel. The motor is doing spring work. This burns out the drive gear, which costs more than the spring would have. We catch this early on service calls in the Ridglea and Wedgwood neighborhoods, where 1980s and 1990s Genie units are still common.
- Visible gap in the spring coil. A torsion spring should be a continuous helix. A gap of even an inch means it’s broken inside the winding and can release stored energy unpredictably. Don’t touch it. We handle the unwinding with proper bars and technique.
Replacement Cost & What’s Included
| Service | Price Range |
|---|---|
| Single torsion spring replacement | $180-$260 |
| Dual torsion spring replacement (recommended for heavier doors) | $260-$340 |
What drives the range: door weight, spring size, whether we’re matching one or two springs, and whether the cables or bearing plates need attention while we’re in there. We quote the flat price before any work begins. No surprises on the bill. The price includes the spring, labor, winding, balance adjustment, and safety check of your Genie opener’s force settings.
Every spring replacement carries our 90-Day Done Right Promise in writing. If it’s not right, we come back. No paperwork to file, no argument.
DIY or Call Us?
There’s a safe middle ground. You can verify the symptoms above, disconnect the opener arm, and try lifting the door manually. If it won’t budge or drops hard, the spring is the problem. Stop there.
What you should not do: unwind a loaded torsion spring with improvised tools. These springs hold enough torque to cause serious injury or worse. The winding bars must fit the cone exactly, and the release technique takes training. We’ve been called to Fort Worth homes where a well-meaning homeowner bent a shaft or stripped a cone, turning a $250 job into a $600 repair.
We’re not here to talk you out of honest work. We’re here because this particular repair carries real risk, and most folks would rather spend their Saturday doing something else. Call (817) 766-2028 and we’ll quote first, then the wrench.
FAQs
Most standard-cycle springs last 7-10 years in Fort Worth’s climate, though we see shorter life when garages face west and bake all afternoon. The heat cycling hardens the steel faster than in milder climates. High-cycle springs rated for 25,000-50,000 cycles last proportionally longer and are worth considering if you use the door four or more times daily. Call (817) 766-2028 and we’ll calculate cycle life for your actual usage.
No. Once a torsion spring breaks or loses its set, it cannot be safely repaired or re-tensioned to factory spec. The metal has fatigued at the molecular level. We replace it with a new spring matched to your door’s exact weight and travel. We also inspect the second spring on dual-spring systems, since matched pairs wear similarly.
Most Genie torsion spring replacements take 45 minutes to an hour from the time we park. We arrive with the common sizes on the truck, so there’s no waiting on parts. The work includes removing the broken spring, installing the new one, winding to proper torque, re-engaging the Genie opener, and testing the safety reverse.
Yes. We carry .218 through .273 wire in the common inside diameters and lengths that fit Fort Worth’s standard residential door sizes. For oddball setups - extra-high doors, custom wood weights, or non-standard shaft sizes - we source overnight and schedule the install next day. We’ll know within five minutes of seeing your door whether we have it.
Ready to get it handled? Call (817) 766-2028 for a free estimate. A live person answers, day or night, and we’ll have you scheduled before you hang up.
Written by Carl Dutton, Owner, Mainspring Garage Door Co. at Mainspring Garage Door Co., serving Fort Worth and nearby areas.